What Is CO₂ Molding? Sodium Silicate (Waterglass) Sand Molding in Casting
CO₂ molding is a sand mold and core process in which sand is mixed with sodium silicate (waterglass) binder and hardened by passing carbon dioxide gas through the mix. It develops handling strength without thermally baking the binder and is used for metal castings, including cast iron and steel parts. Strength for handling is a key benefit; harder shakeout and sensitivity to binder amount and gassing practice are common limits. Both pre-pour mold quality and post-solidification collapsibility should be evaluated before selecting the process.
CO₂ Molding vs “CO₂ Casting”
In CO₂ molding, sand–waterglass mix is formed around a pattern or in a core box, then CO₂ hardens the binder and bonds the sand grains. “CO₂ casting” usually means pouring a casting into a mold or core made this way. CO₂ acts at the mold/core preparation stage; molten metal then fills the cavity and solidifies. The process is a subset of sand casting—the difference from other sand methods is the binder and curing mechanism. Mold choice still depends on material, geometry, quantity, and quality needs.
What Is “CO₂ Sand” Made Of?
“CO₂ sand” is not a separate mineral—it means sand prepared with a binder system cured by CO₂ gas. Typical waterglass system components:
| Material | Role | Selection note |
|---|---|---|
| Base sand (usually foundry silica) | Mold/core body | Grain size, shape, moisture, thermal suitability |
| Sodium silicate (waterglass) | Bonds grains after curing | Grade, concentration, viscosity, addition rate |
| CO₂ gas | Hardens the binder system | Amount, distribution, controlled gassing |
| Compatible additives (if needed) | Adjust collapsibility and other properties | Match binder chemistry and process trials |
Not all waterglass grades are interchangeable. Using waterglass also does not always mean CO₂ curing—ester-cured silicate systems exist. Other CO₂-cured binders (for example some phenolic systems) also exist; presence of CO₂ alone does not identify the binder chemistry.
Simply put, CO₂ reacts with sodium silicate to form a silica gel that bonds sand grains so the pattern or core can be stripped.
CO₂ Molding Steps
- Prepare pattern/core box, sand, and equipment: draft, parting, and tool condition matter—good curing cannot fix a poor pattern. Control sand grain size, moisture, and cleanliness; mixing and gassing equipment should allow measured, repeatable settings.
- Mix sand and sodium silicate: distribute binder uniformly; lumps or lean/rich zones create uneven mold behavior. Do not copy a core mix recipe to a different mold size without trials.
- Form and compact: reproduce shape while leaving permeability for gas. Place gates, risers, and core prints per design. Uniform compaction—especially in corners and thin sections—affects gas distribution and local strength.
- Gas with CO₂: time, flow, and distribution must match mold volume, permeability, and binder. More gas is not always better: under-gassing may leave weak molds; over-gassing can reduce strength during storage. Surface hardness alone does not prove uniform cure.
- Strip and prepare: inspect edges, cavity surfaces, and joints. Apply a compatible refractory coating if needed and dry it per instructions—CO₂ cure does not remove all later drying needs.
- Assemble, pour, shake out: set cores, close and clamp, pour under defined conditions, then break out after adequate cooling. Remove gates/risers, clean, shot-blast, and machine as required.
What Controls CO₂ Mold Quality?
| Parameter | Why it matters | Suggested control |
|---|---|---|
| Sand properties | Mixing, gas passage, surface finish | Check grain size, moisture, fines |
| Binder type and amount | Strength and shakeout behavior | Record grade, weigh additions, trial samples |
| Mixing and compaction | Uniform properties through the mold | Control method and critical zones |
| Gassing | Adequate, even hardening | Record flow, time, and distribution path |
| Storage | Quality until use | Record environment; evaluate stored samples |
| Mold coating | Surface quality and binder compatibility | Select suitable coating and control prep |
Two times matter: mix work life after blending, and mold/core storage life after curing. There is no universal “24-hour” rule—follow binder guidance and shop trials.
Uses in Mold and Core Making
CO₂ systems can make outer molds and internal cores. For a pump casing, the mold cavity forms the exterior while a core forms the fluid path. Access for gassing, assembly strength, and post-cast sand removal must all be workable. The method can serve ferrous and some non-ferrous alloys; sand, coating, and mold design must match iron or steel thermal conditions. Complex cores alone do not justify the process if gassing access or collapsibility is poor.
Advantages
- Hardening without thermal binder bake
- One binder family usable for molds and cores with suitable settings
- Handling strength for transport and assembly
- Useful for many industrial cast shapes when process parameters are controlled
Limitations
- Shakeout can be more difficult than with some other binder systems
- Sensitive to binder amount, mixing uniformity, and gassing practice
- Storage behavior depends on binder, environment, and gassing history
- Reclamation and collapsibility must be planned into the process
When to Choose CO₂ Molding
Consider CO₂ molding when you need chemical-bonded sand strength without baking, for molds or cores of suitable size and geometry, and when your foundry can control mix and gassing consistently. Compare it with green sand, no-bake resin, and other core processes against geometry, alloy, volume, and quality needs. At Taimaz Foolad (Metco), mold and core route selection for cast iron and steel parts follows part geometry, alloy, and quality requirements.
FAQ
Is CO₂ molding a casting process by itself?
It is a sand mold/core hardening method used within sand casting.
Is waterglass always cured with CO₂?
No—other silicate curing systems exist; this article covers the common CO₂-gassed waterglass route.
Does more CO₂ always improve quality?
No. Both under- and over-gassing can harm strength and storage behavior.







