What Is Sand Casting? Steps, Methods, and Industrial Uses

In This Article

Most Popular This Week

Casting Industry Income in Iranian Year ۱۴۰۵: Foundry Wages and Shop/Plant Profit

What Is White Cast Iron? ۳ Main Types, Properties, Uses, and Limits

Article Summary

Sand casting is a common metal-part process in which molten metal is poured into a shaped cavity in a sand mold. After solidification the mold is broken to remove the casting. It is used for parts such as pump casings, valve bodies, gearbox housings, and bearing housings. Suitability depends on mate

What Is Sand Casting? Steps, Methods, and Industrial Uses

Sand casting is a common metal-part process in which molten metal is poured into a shaped cavity in a sand mold. After solidification the mold is broken to remove the casting. It is used for parts such as pump casings, valve bodies, gearbox housings, and bearing housings. Suitability depends on material, geometry, size, quantity, and required quality. The casting is not always ready to install—cleaning, heat treatment, machining, or extra inspection may still be needed.

Taimaz Foolad (Metco) uses sand casting among its routes for custom cast iron and steel industrial parts.

What Is Sand Casting?

In sand casting, molding sand forms a cavity with the desired shape. A pattern is packed in sand, then removed; the remaining cavity receives molten metal, which solidifies into the near-net shape. Molding sand needs heat resistance, adequate strength, and gas permeability. Binders and additives create the required strength depending on the molding system.

In most sand-casting methods the mold is expendable—destroyed to extract the casting—while the pattern can often be reused many times. Used sand may be reclaimed or recycled depending on binder type and plant capability. Pattern reuse, mold reuse, and sand reclamation are three different concepts.

Main Parts of a Sand Mold

ElementRoleWhy it matters
PatternCreates the mold cavity shapeMust allow for shrinkage, draft, and machining stock
FlaskHolds the mold sandSupports mold shape and handling
Cope and dragUpper and lower mold halvesAlignment prevents mismatch
Mold cavityReceives molten metalForms the external casting shape
Gating systemGuides metal into the cavityAffects filling, velocity, and turbulence
Risers / feedersSupply metal during solidificationHelp compensate shrinkage
CoreForms internal spaces and passagesCreates features the pattern alone cannot
VentsHelp gases escapeDesigned with molding method and mold layout

The parting line is where cope and drag meet; its mark may appear on the as-cast surface. The pattern forms the cavity and is removed before pouring in conventional processes; the core stays in the mold so metal solidifies around it and leaves an internal cavity or passage.

Sand Casting Process Steps

  1. Review drawing, alloy, and requirements: size, wall thickness, grade, tolerances, quantity, castability, need for cores, and whether delivery is as-cast or needs machining, heat treatment, finishing, or tests.
  2. Design and make the pattern: wood, metal, or polymer depending on volume. Pattern size is not identical to final part size—shrinkage, draft, parting, and machining allowance are included.
  3. Prepare sand and make the mold: green-sand moisture/strength/compactability or chemical-binder mixing and curing must be controlled. Gating, feeding, and related features are formed per design.
  4. Remove pattern, set cores, close mold: cores for internal passages (for example pump fluid paths) must be located and secured; coatings may be applied before closing.
  5. Prepare and control the melt: chemistry, temperature, and melt treatments differ for iron, steel, and non-ferrous alloys.
  6. Pour and solidify: pouring temperature, fill time, and flow must match geometry and alloy; feeding design reduces shrinkage cavities. Shakeout timing depends on alloy, size, and thermal condition—surface freezing alone does not mean the casting is ready to extract.
  7. Shakeout and remove gating/risers: break the mold, remove sand and core remains, cut off gates/risers; shot blasting or grinding may follow. Compatible sand can enter reclamation.
  8. Finishing and final inspection: cleaning, heat treatment, machining of seal faces, bearing seats, holes, and mating surfaces as required; visual, dimensional, hardness, metallographic, or NDT checks per order. Quality control also runs throughout production.

Sand Molding Methods

Methods are grouped by binder and strengthening mechanism—not by base sand mineral alone. “Silica sand” is a molding material; “CO₂” refers to a binder curing method.

  • Green sand: sand, clay binder, water, and additives; “green” means ready-to-use, not color. Used on manual or mechanized lines; mix control, moisture, strength, and compaction are critical.
  • Sodium silicate + CO₂: sand mixed with waterglass; CO₂ gas hardens the system for molds or cores. Binder amount, gassing, collapsibility, and reclaimability matter.
  • Self-hardening (no-bake) resin sands: binder and hardener cure at ambient temperature (e.g., furan systems). Work time and cure speed must match molding cycle.
  • Dry sand: mold is dried after forming to reduce moisture; not identical to all resin/no-bake systems.
  • Shell molding: sand–resin mix forms a shell on a heated pattern; tooling, geometry, volume, and quality needs drive selection.
MethodStrength mechanismSelection notes
Green sandClay binder + controlled moistureMix, compaction, production conditions
Sodium silicate + CO₂Gas-hardened binder systemStrength, shakeout, sand reclaim
Self-hardening resinAmbient binder–hardener reactionWork time, cure speed, cost
Dry sandDrying after mold formingTime, equipment, mold properties
Shell moldingHeat-formed resin-sand shellTooling, geometry, quality, volume

Cold-box and hot-box terms usually refer to coremaking, not necessarily the main mold system.

Sands Used in Casting

Silica sand is common; chromite or zircon sands may be used for demanding thermal or surface needs. Finer grains can improve surface finish but may reduce permeability. Sand choice must match alloy, pouring temperature, molding method, and plant conditions.

Typical Industrial Applications

Part groupExamplesKey manufacturing notes
Pump partsCasing, impeller, diffuserInternal geometry, wall thickness, mating faces, machining
Valve partsBody and coverInternal quality, flow path, sealing faces
Power-transmission housingsGearbox and bearing housingsOverall size, mounting locations, machined accuracy
Machinery partsBodies, housings, industrial componentsLoading, geometry, size, duty

Advantages and Limits

  • Advantages: flexible geometries including internal passages with cores; wide size range; suitable for many iron and steel industrial parts; patterns reusable; tooling often more economical than permanent molds for varied or lower-volume work.
  • Limits: as-cast accuracy and finish vary by process; molds are usually single-use; dimensional capability, minimum wall, and surface quality are not the same for every sand process; finishing is often required.

When to Choose Sand Casting

Consider sand casting when the part is a castable metal shape with volumetric form or internal features, when machining from solid would waste excess stock, and when quantity, geometry, and quality fit a sand process. Provide drawing or sample, alloy grade, quantity, duty, and finishing/inspection needs. Taimaz Foolad (Metco) reviews sand-cast iron and steel industrial parts from roughly 150 g to 2,000 kg depending on geometry and specifications.

FAQ

Is sand casting the same as green-sand molding?
No. Sand casting is the overall process; green sand is one molding system among several.

Are castings ready to install after shakeout?
Often not—cleaning, heat treatment, machining, and inspection may still be required.

What is the difference between pattern and core?
The pattern forms the mold cavity and is usually removed before pouring; the core remains in the mold to create internal spaces.

Leave a Comment

Your email address will not be published. Required fields are marked *

Related Articles

Shopping Cart

ارسال مشخصات قطعه

مشخصات، نقشه یا تصویر قطعه را ارسال کنید تا کارشناسان تایماز فولاد با شما تماس بگیرند.

    افزودن نقشه، تصویر یا فایل قطعه

    فایل یا تصویر خود را انتخاب کنید یا بکشید و در این قسمت رها کنید.

    JPG, PNG, PDF, DWG, STEP

    Scroll to Top

    ارسال مشخصات قطعه

    مشخصات، نقشه یا تصویر قطعه را ارسال کنید تا کارشناسان تایماز فولاد با شما تماس بگیرند.

      افزودن نقشه، تصویر یا فایل قطعه

      فایل یا تصویر خود را انتخاب کنید یا بکشید و در این قسمت رها کنید.

      JPG, PNG, PDF, DWG, STEP